BLOCKADE BAR



DOOR LOCK GUARDS


      • 250 Door Armor.

        For Key In Knob Locsk.

        Photo by: Major Manufacturing

      • 250 Door Armor For Key In Knob Lock:

        Our new lock guard is designed to protect key-in-knob locks against pipe wrench and beating attacks. The base plate measures 3-1/2" square and will accommodate locks with rose diameters up to 2-11/16 inches, guard projection is 3 inches.

        Four 1/4" carriage bolts are supplied for mounting on doors up to 1-3/4 inch thick. Finish is an exterior silver powdercoat. Best results are obtained using a storeroom function lock.

        Lock Not Included.

      • 260 Door Armor.

        For Deadbolt Locks.

        Photo by: Major Manufacturing

      • 260 Door Armor For Deadbolt Locks:

        Our new lock guard is designed to protect deadbolt locks against pipe wrench and beating attacks. The base plate measures 3-1/2" square and will accommodate locks with rose diameters up to 2-11/16 inches, guard projection is 3 inches.

        Four 1/4" carriage bolts are supplied for mounting on doors up to 1-3/4 inch thick. Finish is an exterior silver powdercoat. Best results are obtained using a storeroom function lock.

        Lock Not Included.

      • AG5-A Aluma-Guard.

        Aluminum Powdercoat.

        Photo by: Major Manufacturing

      • AG5-A Aluma-Guard Aluminum Powdercoat:

        Our new Aluma-Guard is designed to protect aluminum framed, glass, store front doors. It forms a shield that will protect both the latch area from attack and the lock cylinder from wrenching.

        The AG-5 is formed from cold rolled steel that is 6-1/2" high, 3-1/2" wide & 7/64" thick.

        Mounting is easy with one carriage bolt in the top and a drive rivet in the bottom and can be installed with the lock still in the door. Available in aluminum and duranodic powdercoat finishes.

      • AG5-D Aluma-Guard.

        Duranodic Powdercoat.

        Photo by: Major Manufacturing

      • AG5-D Aluma-Guard Duranodic Powdercoat:

        Our new Aluma-Guard is designed to protect aluminum framed, glass, store front doors. It forms a shield that will protect both the latch area from attack and the lock cylinder from wrenching.

        The AG-5 is formed from cold rolled steel that is 6-1/2" high, 3-1/2" wide & 7/64" thick.

        Mounting is easy with one carriage bolt in the top and a drive rivet in the bottom and can be installed with the lock still in the door. Available in aluminum and duranodic powdercoat finishes.

      • AG1-A Aluma-Guard.

        Aluminum Color.

        Photo by: Major Manufacturing

      • AG1-A Aluma-Guard Aluminum Color:

        Standard "Aluma-Guard" for use on outswinging offset hung aluminum doors. Complete with all mounting hardware and directions. 6-7/8" high x 4-1/8" wide.

      • AG1-D Aluma-Guard.

        Duranodic Color.

        Photo by: Major Manufacturing

      • AG1-D Aluma-Guard Duranodic Color:

        Standard "Aluma-Guard" for use on outswinging offset hung aluminum doors. Complete with all mounting hardware and directions. "Duranodic Powdercoat". 6-7/8" high x 4-1/8" wide.

      • AG1B-A Aluma-Guard.

        Blank Plate, Aluminum Color.

        Photo by: Major Manufacturing

      • AG1B-A Aluma-Guard Blank Plate, Aluminum Color:

        Same as standard "Aluma-Guard" but without keyhole. Perfect for use on locks when no key access is required. Can be modified by customer for special application. "Aluminum Powdercoat". 6-7/8" high x 4-1/8" wide.

      • AG1B-D Aluma-Guard.

        Blank Plate, Duranodic Color.

        Photo by: Major Manufacturing

      • AG1B-D Aluma-Guard Blank Plate, Duranodic Color:

        Same as standard "Aluma-Guard" but without keyhole. Perfect for use on locks when no key access is required. Can be modified by customer for special application. "Duranodic Powdercoat". 6-7/8" high x 4-1/8" wide.

      • AG3L-A Aluma Guard.

        ADA Left Side Aluminum.

        Photo by: Major Manufacturing

      • AG3L-A Aluma Guard ADA Left Side Aluminum:

        The same high security Aluma Guard plate as our standard AG-1 model except for an offset cylinder hole that allows installing on doors where the lock is mounted closer to the push bar.

        The distance from the top of the plate to the center of the 7/8" diameter cylinder hole is 2-7/8". Models available for both left and right hand mounting. "Aluminum Powdercoat". 6-7/8" high x 4-1/8" wide.

      • AG3L-D Aluma Guard.

        ADA Left Side Duranodic.

        Photo by: Major Manufacturing

      • AG3L-D Aluma Guard ADA Left Side Duranodic:

        The same high security Aluma Guard plate as our standard AG-1 model except for an offset cylinder hole that allows installing on doors where the lock is mounted closer to the push bar.

        The distance from the top of the plate to the center of the 7/8" diameter cylinder hole is 2-7/8". Models available for both left and right hand mounting. "Duranodic Powdercoat". 6-7/8" high x 4-1/8" wide.

      • AG3R-A Aluma Guard.

        ADA Right Side Aluminum.

        Photo by: Major Manufacturing

      • AG3R-A Aluma Guard ADA Right Side Aluminum:

        The same high security Aluma Guard plate as our standard AG-1 model except for an offset cylinder hole that allows installing on doors where the lock is mounted closer to the push bar.

        The distance from the top of the plate to the center of the 7/8" diameter cylinder hole is 2-7/8". Models available for both left and right hand mounting. "Aluminum Powdercoat". 6-7/8" high x 4-1/8" wide.

      • AG3R-D Aluma Guard.

        ADA Right Side Duranodic.

        Photo by: Major Manufacturing

      • AG3R-D Aluma Guard ADA Right Side Duranodic:

        The same high security Aluma Guard plate as our standard AG-1 model except for an offset cylinder hole that allows installing on doors where the lock is mounted closer to the push bar.

        The distance from the top of the plate to the center of the 7/8" diameter cylinder hole is 2-7/8". Models available for both left and right hand mounting. "Duranodic Powdercoat". 6-7/8" high x 4-1/8" wide.

      • AG4-A Aluma-Guard.

        For IC Cylinders.

        Photo by: Major Manufacturing

      • AG4-A Aluma-Guard for IC Cylinders:

        Special "Aluma-Guard" for use with longer 6- and 7-pin cylinders or best type interchangeable core cylinders. "Aluminum Powdercoat." 6-7/8" high x 4-1/8" wide.

      • AG4-D Aluma-Guard.

        For IC Cylinders.

        Photo by: Major Manufacturing

      • AG4-D Aluma-Guard for IC Cylinders:

        Special "Aluma-Guard" for use with longer 6- and 7-pin cylinders or best type interchangeable core cylinders. "Duranodic Powdercoat." 6-7/8" high x 4-1/8" wide.

      • SGA-1 Strike Guard.

        Aluminum Color.

        Photo by: Major Manufacturing

      • SGA-1 Strike Guard - Aluminum Color:

        Used to repair an aluminum door jamb that has been damaged die to a break-in, or to reinforce a jamb as extra protection against forced entry. This Strike/Cylinder Gard package can be an easy add on sale when installing, servicing or changing the combinations on aluminum doors.

        Thin flat design will allow strike to be installed on door frame and not rub the door. Packed with our CGA or CGD Cylinder Gard at no extra charge to make an aluminum door security package.

        Will work with W & F and Reflectolite type locks or punch out the "Knock-Out" and use with Adams Rite type swing bolt locks. Will fit 4" or 41/2" wide jambs. Easily installed by drilling six No. 20 holes in the door frame and using the steel pop rivets supplied with the strike. 14 Gauge cold rolled steel 2-15/16" x 8" 1. Approximately 5/64" thick.

      • SGD-1 Strike Guard.

        Duranodic Color.

        Photo by: Major Manufacturing

      • SGD-1 Strike Guard - Duranodic Color:

        Used to repair an aluminum door jamb that has been damaged die to a break-in, or to reinforce a jamb as extra protection against forced entry. This Strike/Cylinder Gard package can be an easy add on sale when installing, servicing or changing the combinations on aluminum doors.

        Thin flat design will allow strike to be installed on door frame and not rub the door. Packed with our CGA or CGD Cylinder Gard at no extra charge to make an aluminum door security package.

        Will work with W & F and Reflectolite type locks or punch out the "Knock-Out" and use with Adams Rite type swing bolt locks. Will fit 4" or 41/2" wide jambs. Easily installed by drilling six No. 20 holes in the door frame and using the steel pop rivets supplied with the strike. 14 Gauge cold rolled steel 2-15/16" x 8" 1. Approximately 5/64" thick.

      • 203-A Steel Guard Plate.

        With 3/16" Rise - Aluminum.

        Photo by: Major Manufacturing

      • 203-A Steel Guard Plate With 3/16" Rise - Aluminum:

        Steel guard plate with 3/16" rise and 13/16" cylinder hole in center. May be used with 210 riser plate. Aluminum powdercoat finish. Supplied with mounting hardware.

      • 203-D Steel Guard Plate.

        With 3/16" Rise - Duranodic.

        Photo by: Major Manufacturing

      • 203-D Steel Guard Plate With 3/16" Rise - Duranodic:

        Steel guard plate with 3/16" rise and 13/16" cylinder hole in center. May be used with 210 riser plate. Duranodic powdercoat finish. Supplied with mounting hardware.

      • 205-A Steel Guard Plate.

        With 5/16" Rise - Aluminum.

        Photo by: Major Manufacturing

      • 205-A Steel Guard Plate With 5/16" Rise - Aluminum:

        Steel guard plate with 5/16" rise and 13/16" cylinder hole in center. May be used with 210 riser plate. Aluminum powdercoat finish. Supplied with mounting hardware.

      • 100-A Rim Cylinder Guard.

        Flat Plate - Aluminum.

        Photo by: Major Manufacturing

      • 100-A Rim Cylinder Guard Flat Plate - Aluminum:

        Rim cylinder guard flat plate. Aluminum powdercoat.

      • 100-D Rim Cylinder Guard.

        Flat Plate - Duranodic.

        Photo by: Major Manufacturing

      • 100-D Rim Cylinder Guard Flat Plate - Duranodic:

        Rim cylinder guard flat plate. Duranodic powdercoat.

      • 103-A Rim Cylinder Guard.

        3/16" Center Rise - Aluminum.

        Photo by: Major Manufacturing

      • 103-A Rim Cylinder Guard 3/16" Center Rise - Aluminum:

        Rim cylinder guard 3/16" center rise. Aluminum powdercoat.

      • 103-D Rim Cylinder Guard.

        3/16" Center Rise - Duranodic.

        Photo by: Major Manufacturing

      • 103-D Rim Cylinder Guard 3/16" Center Rise - Duranodic:

        Rim cylinder guard 3/16" center rise. Duranodic powdercoat.


FILE CABINET LOCK BARS


      • FB-1L File Cabinet Locking Bar.

        18-3/4" OAL - LH Mount.

        Photo by: Major Manufacturing

      • FB-1L File Cabinet Locking Bar - 18-3/4" OAL - LH Mount:

        File Cabinet Locking Bars: File cabinet locking bar mounts on left hand side of cabinet for standard applications. A right hand model is also available for special applications. Will not block adjoining cabinets in either locked or unlocked position.

        Red tape strip on inside of locking bar indicates unlocked position and protects painted finish on filing cabinet when locked. May also be used to lock sliding drawers on rollaway cabinets or any cabinet with steel drawers.

        Individually boxed with fasteners, padlock not included.

      • FB-1R File Cabinet Locking Bar.

        18-3/4" OAL - RH Mount.

        Photo by: Major Manufacturing

      • FB-1R File Cabinet Locking Bar - 18-3/4" OAL - RH Mount:

        File Cabinet Locking Bars: File cabinet locking bar mounts on left hand side of cabinet for standard applications. A right hand model is also available for special applications. Will not block adjoining cabinets in either locked or unlocked position.

        Red tape strip on inside of locking bar indicates unlocked position and protects painted finish on filing cabinet when locked. May also be used to lock sliding drawers on rollaway cabinets or any cabinet with steel drawers.

        Individually boxed with fasteners, padlock not included.

      • FB-2L File Cabinet Locking Bar.

        23-1/2" OAL - LH Mount 2 Drawers.

        Photo by: Major Manufacturing

      • FB-2L File Cabinet Locking Bar - 23-1/2" OAL:

        File Cabinet Locking Bars: File cabinet locking bar mounts on left hand side of cabinet for standard applications. A right hand model is also available for special applications. Will not block adjoining cabinets in either locked or unlocked position.

        Red tape strip on inside of locking bar indicates unlocked position and protects painted finish on filing cabinet when locked. May also be used to lock sliding drawers on rollaway cabinets or any cabinet with steel drawers.

        Individually boxed with fasteners, padlock not included.

      • FB-2R File Cabinet Locking Bar.

        23-1/2" OAL - RH Mount 2 Drawers.

        Photo by: Major Manufacturing

      • FB-2R File Cabinet Locking Bar - 23-1/2" OAL:

        File Cabinet Locking Bars: File cabinet locking bar mounts on left hand side of cabinet for standard applications. A right hand model is also available for special applications. Will not block adjoining cabinets in either locked or unlocked position.

        Red tape strip on inside of locking bar indicates unlocked position and protects painted finish on filing cabinet when locked. May also be used to lock sliding drawers on rollaway cabinets or any cabinet with steel drawers.

        Individually boxed with fasteners, padlock not included.

      • FB-3L File Cabinet Locking Bar.

        33" OAL - LH Mount 3 Drawers.

        Photo by: Major Manufacturing

      • FB-3L File Cabinet Locking Bar - 33" OAL:

        File Cabinet Locking Bars: File cabinet locking bar mounts on left hand side of cabinet for standard applications. A right hand model is also available for special applications. Will not block adjoining cabinets in either locked or unlocked position.

        Red tape strip on inside of locking bar indicates unlocked position and protects painted finish on filing cabinet when locked. May also be used to lock sliding drawers on rollaway cabinets or any cabinet with steel drawers.

        Individually boxed with fasteners, padlock not included.

      • FB-3R File Cabinet Locking Bar.

        33" OAL - RH Mount 3 Drawers.

        Photo by: Major Manufacturing

      • FB-3R File Cabinet Locking Bar - 33" OAL:

        File Cabinet Locking Bars: File cabinet locking bar mounts on left hand side of cabinet for standard applications. A right hand model is also available for special applications. Will not block adjoining cabinets in either locked or unlocked position.

        Red tape strip on inside of locking bar indicates unlocked position and protects painted finish on filing cabinet when locked. May also be used to lock sliding drawers on rollaway cabinets or any cabinet with steel drawers.

        Individually boxed with fasteners, padlock not included.

      • FB-4L File Cabinet Locking Bar.

        49-1/2" OAL - LH Mount 4 Drawers.

        Photo by: Major Manufacturing

      • FB-4L File Cabinet Locking Bar - 49-1/2" OAL:

        File Cabinet Locking Bars: File cabinet locking bar mounts on left hand side of cabinet for standard applications. A right hand model is also available for special applications. Will not block adjoining cabinets in either locked or unlocked position.

        Red tape strip on inside of locking bar indicates unlocked position and protects painted finish on filing cabinet when locked. May also be used to lock sliding drawers on rollaway cabinets or any cabinet with steel drawers.

        Individually boxed with fasteners, padlock not included.

      • FB-4R File Cabinet Locking Bar.

        49-1/2" OAL - RH Mount 4 Drawers.

        Photo by: Major Manufacturing

      • FB-4R File Cabinet Locking Bar - 49-1/2" OAL:

        File Cabinet Locking Bars: File cabinet locking bar mounts on left hand side of cabinet for standard applications. A right hand model is also available for special applications. Will not block adjoining cabinets in either locked or unlocked position.

        Red tape strip on inside of locking bar indicates unlocked position and protects painted finish on filing cabinet when locked. May also be used to lock sliding drawers on rollaway cabinets or any cabinet with steel drawers.

        Individually boxed with fasteners, padlock not included.

      • FB-5L File Cabinet Locking Bar.

        55" OAL - LH Mount 5 Drawers.

        Photo by: Major Manufacturing

      • FB-5L File Cabinet Locking Bar - 55" OAL:

        File Cabinet Locking Bars: File cabinet locking bar mounts on left hand side of cabinet for standard applications. A right hand model is also available for special applications. Will not block adjoining cabinets in either locked or unlocked position.

        Red tape strip on inside of locking bar indicates unlocked position and protects painted finish on filing cabinet when locked. May also be used to lock sliding drawers on rollaway cabinets or any cabinet with steel drawers.

        Individually boxed with fasteners, padlock not included.

      • FB-5R File Cabinet Locking Bar.

        55" OAL - RH Mount 5 Drawers.

        Photo by: Major Manufacturing

      • FB-5R File Cabinet Locking Bar - 55" OAL:

        File Cabinet Locking Bars: File cabinet locking bar mounts on left hand side of cabinet for standard applications. A right hand model is also available for special applications. Will not block adjoining cabinets in either locked or unlocked position.

        Red tape strip on inside of locking bar indicates unlocked position and protects painted finish on filing cabinet when locked. May also be used to lock sliding drawers on rollaway cabinets or any cabinet with steel drawers.

        Individually boxed with fasteners, padlock not included.


HINGE PINS


      • JP-10 Hinge Pins.

        For use on wood or metal doors and jambs.

        Photo by: Major Manufacturing

      • JP-10 Hinge Pins:

        For residential hinges using #10 screw. Simply remove one opposing screw from each hinge leaf and replace with the proper size Jamb Pin. Secures door in jamb when closed if hinge pin is removed.

        For use on wood or metal doors and jambs. Jamb Pins have a combination wood and machine thread. Machine screw thread is 10-24. 2 pins per pack.

      • JP-10-100 Hinge Pins (100 Per Pack).

        For use on wood or metal doors and jambs.

        Photo by: Major Manufacturing

      • JP-10-100 Hinge Pins (100 Per Pack):

        For residential hinges using #10 screw. Simply remove one opposing screw from each hinge leaf and replace with the proper size Jamb Pin. Secures door in jamb when closed if hinge pin is removed.

        For use on wood or metal doors and jambs. Jamb Pins have a combination wood and machine thread. Machine screw thread is 10-24. JP-10-100: Bulk Pack. 100 per pack.

      • JP-12 Jamp Pins.

        For use on wood or metal doors and jambs.

        Photo by: Major Manufacturing

      • JP-12 Jamp Pins:

        For commercial hinges using #12 screw. Simply remove one opposing screw from each hinge leaf and replace with the proper size Jamb Pin. Secures door in jamb when closed if hinge pin is removed.

        For use on wood or metal doors and jambs. Jamb Pins have a combination wood and machine thread. Machine screw thread is 12-24. 2 pins per pack.

      • JP-12-100 Jamb Pins (100 Per Pack).

        For use on wood or metal doors and jambs.

        Photo by: Major Manufacturing

      • JP-12-100 Jamb Pins (100 Per Pack):

        For commercial hinges using #12 screw. Simply remove one opposing screw from each hinge leaf and replace with the proper size Jamb Pin. Secures door in jamb when closed if hinge pin is removed.

        For use on wood or metal doors and jambs. Jamb Pins have a combination wood and machine thread. Machine screw thread is 12-24. Bulk Pack. 100 per pack.

      • JP-22 Jamb Pins.

        For added security on hinge side of door.

        Photo by: Major Manufacturing

      • JP-22 Jamb Pins:

        Jamb pin for added security on hinge side of door. JP-22 may have to be mortised flush on tight fitting doors. Packed two per bag with fasteners. Zinc plated.

        To install, drill a 1/4" hole in center of door frame and secure with mounting screws (supplied). Drill a 1/2" hole in the door to receive pin and installation is complete.

      • JP-25 Jamb Pins.

        For use on wood and metal doors.

        Photo by: Major Manufacturing

      • JP-25 Jamb Pins:

        By installing in the jamb and drilling a strike hole in the door, the door will not be able to be removed when locked; if the hinge pins are removed.

        For use on wood and metal doors. Can be screwed into a wood jamb after tapping a 1/4-20 threaded hole. 2 pins per pack.


JAMB JACKETS


      • JJB-134-24 Jamb Jacket.

        1-3/4 x 24" in design.

        Photo by: Major Manufacturing

      • JJB-134-24:

        JJB-134-24 is 24" in length for 1-3/4" doors. Repairs and covers damaged and splitout door jambs without the expense of replacing the whole jamb. Adds reinforcement to healthy undamaged jambs for additional security. Non-handed. Can be used on right or left hand doors.

        Designed to cover standard l/2" rabbeted jamb. Finished in Beige Powdercoat finish for durability. (May be repainted to match existing frame.) Supplied with mounting screws. NOTE: This is a blank plate with no strike recess.

      • JJB-134-36 Jamb Jacket.

        1-3/4 x 36" in design.

        Photo by: Major Manufacturing

      • JJB-134-36:

        JJB-134-24 is 36" in length for 1-3/4" doors. Repairs and covers damaged and splitout door jambs without the expense of replacing the whole jamb. Adds reinforcement to healthy undamaged jambs for additional security. Non-handed. Can be used on right or left hand doors.

        Designed to cover standard l/2" rabbeted jamb. Finished in Beige Powdercoat finish for durability. (May be repainted to match existing frame.) Supplied with mounting screws. NOTE: This is a blank plate with no strike recess.

      • JJD-134-36 Jamb Jacket.

        Double Strike 1-3/4 x 36" in design.

        Photo by: Major Manufacturing

      • JJD-134-36 - Double Strike:

        Our new Jamb Jacket is to be used with a cylindrical lock or lever with a deadbolt mounted above. The double strike model has the strike plates mounted with a 5-1/2 inch center to center spacing.

        It is designed for a 1-3/4" jamb and is mounted with 10 #10 screws 2-1/2" long. The Jamb Jacket is made from sheet metal approximately 1/16 inches thick and finished in almond Powdercoat.

      • JJE-134-16 Jamb Jacket.

        1-3/4 x 16" in design.

        Photo by: Major Manufacturing

      • JJE-134-16 Jamb Jacket:

        "Econo Gard' is available in 16" length only and is not recessed to accommodate T-strike. Packaged with mounting screws.

      • JJE-138-16 Jamb Jacket.

        1-3/8 x 16" in design.

        Photo by: Major Manufacturing

      • JJE-138-16 Jamb Jacket:

        "Econo Gard' is available in 16" length only and is not recessed to accommodate T-strike. Packaged with mounting screws.

      • JJL-134-24 Jam Jacket.

        1-3/4" x 24" in design.

        Photo by: Major Manufacturing

      • JJL-134-24 Jamb Jacket:

        "Jamb Jacket" is recessed to accommodate T-strike. JJL-134-24 is 24" in length for 1-3/4" doors. Repairs and covers damaged and splitout door jambs without the expense of replacing the whole jamb. Adds reinforcement to healthy undamaged jambs for additional security.

        Non-handed. Can be used on right or left hand doors. Designed to cover standard l/2" rabbeted jamb. Finished in Beige Powdercoat finish for durability. (May be repainted to match existing frame.) Supplied with strike plate and mounting screws.

      • JJL-134-36 Jamb Jacket.

        1-3/4" x 36" in design.

        Photo by: Major Manufacturing

      • JJL-134-36 Jamb Jacket:

        "Jamb Jacket" is recessed to accommodate T-strike. JJL-134-36 is 36" in length for 1-3/4" doors. Repairs and covers damaged and splitout door jambs without the expense of replacing the whole jamb. Adds reinforcement to healthy undamaged jambs for additional security. Non-handed. Can be used on right or left hand doors.

        Designed to cover standard l/2" rabbeted jamb. Finished in Beige Powdercoat finish for durability. (May be repainted to match existing frame.) Supplied with strike plate and mounting screws.

      • JJL-134-72 Jamb Jacket.

        1-3/4" x 72" in design.

        Photo by: Major Manufacturing

      • JJL-134-72 Jamb Jacket:

        "Jamb Jacket" is recessed to accommodate T-strike. JJL-134-72 is 72" in length for 1-3/4" doors. Repairs and covers damaged and splitout door jambs without the expense of replacing the whole jamb. Adds reinforcement to healthy undamaged jambs for additional security. Non-handed. Can be used on right or left hand doors.

        Designed to cover standard l/2" rabbeted jamb. Finished in Beige Powdercoat finish for durability. (May be repainted to match existing frame.) Supplied with strike plate and mounting screws.

      • JJL-138-24 Jamb Jacket.

        1-3/8" x 24" in design.

        Photo by: Major Manufacturing

      • JJL-138-24 Jamb Jacket:

        "Jamb Jacket" is recessed to accommodate T-strike. JJL-138-24 is 24" in length for 1-3/8" doors. Repairs and covers damaged and splitout door jambs without the expense of replacing the whole jamb. Adds reinforcement to healthy undamaged jambs for additional security. Non-handed. Can be used on right or left hand doors.

        Designed to cover standard l/2" rabbeted jamb. Finished in Beige Powdercoat finish for durability. (May be repainted to match existing frame.) Supplied with strike plate and mounting screws.

      • JJL-138-36 Jamb Jacket.

        1-3/8" x 36" in design.

        Photo by: Major Manufacturing

      • JJL-138-36 Jamb Jacket:

        "Jamb Jacket" is recessed to accommodate T-strike. JJL-138-36 is 36" in length for 1-3/8" doors. Repairs and covers damaged and splitout door jambs without the expense of replacing the whole jamb. Adds reinforcement to healthy undamaged jambs for additional security. Non-handed. Can be used on right or left hand doors.

        Designed to cover standard l/2" rabbeted jamb. Finished in Beige Powdercoat finish for durability. (May be repainted to match existing frame.) Supplied with strike plate and mounting screws.

      • JJL-138-72 Jamb Jacket.

        1-3/8" x 72" in design.

        Photo by: Major Manufacturing

      • JJL-138-72 Jamb Jacket:

        "Jamb Jacket" is recessed to accommodate T-strike. JJL-138-72 is 72" in length for 1-3/8" doors. Repairs and covers damaged and splitout door jambs without the expense of replacing the whole jamb. Adds reinforcement to healthy undamaged jambs for additional security. Non-handed. Can be used on right or left hand doors.

        Designed to cover standard l/2" rabbeted jamb. Finished in Beige Powdercoat finish for durability. (May be repainted to match existing frame.) Supplied with strike plate and mounting screws.


LOCK CYLINDER ACCESSORIES


      • CG2-3 Cylinder Guard.

        Full 2" diameter Brass Ring.

        Photo by: Major Manufacturing

      • CG2-3:

        Free-spinning tapered cone shape. Resistant to channel locks, vise grips, pipe wrenches, etc. Tough, hardened steel for durability. Wave washer supplied to eliminate sloppiness of installation.

        Full 2" diameter. Available in economy and architectural finishes. Cylinder guard plated polished brass. 1 per Pack.

      • CG2-10B Cylinder Guard.

        Full 2" diameter Oil Bronze Ring.

        Photo by: Major Manufacturing

      • CG2-10B:

        Free-spinning tapered cone shape. Resistant to channel locks, vise grips, pipe wrenches, etc. Tough, hardened steel for durability. Wave washer supplied to eliminate sloppiness of installation.

        Full 2" diameter. Available in economy and architectural finishes. Cylinder Guard plated oil rubbed bronze. 1 per Pack.

      • CG2-26D Cylinder Guard.

        Full 2" diameter Satin Chrome Ring.

        Photo by: Major Manufacturing

      • CG2-26D:

        Free-spinning tapered cone shape. Resistant to channel locks, vise grips, pipe wrenches, etc. Tough, hardened steel for durability. Wave washer supplied to eliminate sloppiness of installation.

        Full 2" diameter. Available in economy and architectural finishes. Cylinder Guard plated satin chrome. 1 per Pack.

      • CG-3 Cylinder Guard.

        Full 2" diameter Brass Ring.

        Photo by: Major Manufacturing

      • CG-3:

        Free-spinning tapered cone shape. Resistant to channel locks, vise grips, pipe wrenches, etc. Tough, hardened steel for durability. Wave washer supplied to eliminate sloppiness of installation. Also larger size for longer 6 & 7 pin & interchangeable core type mortise & rim cylinders. Polished Brass Plated / 1 per Pack.

      • CG-10B Cylinder Guard.

        Full 2" diameter Oil Bronze Ring.

        Photo by: Major Manufacturing

      • CG-10B:

        Free-spinning tapered cone shape. Resistant to channel locks, vise grips, pipe wrenches, etc. Tough, hardened steel for durability. Wave washer supplied to eliminate sloppiness of installation.

        Also larger size for longer 6 & 7 pin & interchangeable core type mortise & rim cylinders. Oil Rubbed Bronze Plated / 1 per Pack.

      • CG-26D Cylinder Guard.

        Full 2" diameter Satin Chrome Ring.

        Photo by: Major Manufacturing

      • CG-26D:

        Free-spinning tapered cone shape. Resistant to channel locks, vise grips, pipe wrenches, etc. Tough, hardened steel for durability. Wave washer supplied to eliminate sloppiness of installation. Also larger size for longer 6 & 7 pin & interchangeable core type mortise & rim cylinders. Satin Chrome Plated / 1 per Pack.

      • CCA-332.

        3/32" Aluminum Color Collar.

        Photo by: Major Manufacturing

      • CCA-332:

        3/32" Collar, Aluminum Color, pack of 6.

      • CCB-332.

        3/32" Brass Color Collar.

        Photo by: Major Manufacturing

      • CCB-332:

        3/32" Collar, Brass Color, pack of 6.

      • CCD-332.

        3/32" Duranodic Color Collar.

        Photo by: Major Manufacturing

      • CCD-332:

        3/32" Collar, Duranodic Color, pack of 6.

      • CAK-15.

        Cylinder Accessory Kit.

        Photo by: Major Manufacturing

      • CAK-15:

        The CAK-15 is a new cylinder accessory kit that contains an assortment of popular hardened cylinder gards, plus cylinder collars molded from an "Engineered Plastic". Unlike steel or aluminum that can chip, scratch or bend, collars from engineered plastic will not loose their finish or shape.

        They also resist damage due to the ozone and by ultra violet rays. The kit is packed in a handy plastic box for storage and part numbers are identified for reordering.


LOCKING BOLTS


      • 74 Series Locking Neck Bolt.

        Photo by: Major Manufacturing

      • 74 Series - Locking Neck Bolt:

        Smaller 4" version of model 79 bolt. 4" locking neck bolt complete with two types os strikes and fastners. Laminated bolt has a full 1-1/8" throw and can be locked in the open or closed position.

        Offset of neck bolt is 3/4". Base size is 2" x 4-1/2". Will accept padlocks with shackles up to 1/4" diameter. Steel body in zinc plated.

      • 76 Series.

        Locking Surface Bolt.

        Photo by: Major Manufacturing

      • 76 Series - Locking Surface Bolt:

        6" locking surface bolt complete with two types of strikes and fasteners. Laminated bolt has a full 1-1/8" throw and can be locked in the open or closed position.

        Base size is 2" x 5-1/2". Will accept padlocks with shackles up to 11/32" diameter. Steel body is zinc plated.

      • 79 Series.

        9" locking neck bolt.

        Photo by: Major Manufacturing

      • 79 Series - 9" locking neck bolt:

        Large 9" locking neck bolt complete with two types of strikes and fasteners. Laminated bolt has a full 1-1/2" throw and can be locked in the open or closed position. Offset of neck bolt is 1-1/4".

        Base size is 2-3/4" x 9". Will accept padlocks with shackles up to 7/16" diameter. Steel body is zinc plated.

      • A500L Series.

        Garage Blok - Left Side.

        Photo by: Major Manufacturing

      • A500L Series - Garage Blok for Right Side:

        For left side of door, Garageblok is Jimmie-proof, fortress-like shield for the garage, warehouse, overhead or swinging doors and many other applications.

        • Incorporates a hardened steel bolt and built-in "lock shield" which all but eliminates sawing either in half.
        • 5/8" hardened steel locking bolt featuring a centered point for pin-pointing drilling accuracy.

        • Protective padlock shield.

        • Tough, armored 2 1/4" pound 3/16" steel housing, plated in zinc chromate.

        • Anchored by four 5/16" carriage bolts, washers and nuts supplied for mounting.

        • Blok can be locked in open bolt position to prevent theft of padlock or door being inadvertently locked.

        • Available in both right and left side models.

        • Easily installed in minutes.

      • A500R Series.

        Garage Blok - Right Side.

        Photo by: Major Manufacturing

      • A500L Series - Garage Blok for Right Side:

        For right side of door, Garageblok is Jimmie-proof, fortress-like shield for the garage, warehouse, overhead or swinging doors and many other applications.

        • Incorporates a hardened steel bolt and built-in "lock shield" which all but eliminates sawing either in half.
        • 5/8" hardened steel locking bolt featuring a centered point for pin-pointing drilling accuracy.

        • Protective padlock shield.

        • Tough, armored 2 1/4" pound 3/16" steel housing, plated in zinc chromate.

        • Anchored by four 5/16" carriage bolts, washers and nuts supplied for mounting.

        • Blok can be locked in open bolt position to prevent theft of padlock or door being inadvertently locked.

        • Available in both right and left side models.

        • Easily installed in minutes.


LOCK MOUNT BRACKETS


      • LMB-01 - Lock Mount Bracket.

        For Tubular Latch In Hollow Metal Door.

        Photo by: Major Manufacturing

      • LMB-01 - Lock Mount Bracket:

        The LMB-01 will make installing cylindrical knob locks or dead-bolts on metal doors now faster and easier than ever. The LMB-01 mounting bracket is stamped from 11 gauge cold rolled steel for strength, installed with pop-rivets for convenience, and supplied with an adhesive template for accuracy.

        The LMB-01 mounting bracket is also cut out in the center to allow installations on metal doors with a center seam. The template is marked for 1" and 1 1/8" faceplate cutouts as well as for bracket mounting holes and center lines to locate the crossbore. LMB-01 is supplied complete with template and steel pop-rivets.

      • LMB-02 - Lock Mount Bracket.

        For Mortise Lock In Hollow Metal Doors.

        Photo by: Major Manufacturing

      • LMB-02 - For Mortise Lock In Hollow Metal Doors:

        The LMB-02 mortise lock bracket is designed to be used on metal doors with or without a center seam. Stamped from 11 gage cold rolled steel as the LMB-01 and also mounted with pop-rivets (supplied) for ease of installation.

        The mounting holes are tapped for 12-24 to accommodate existing mortise lock screws supplied by the manufacturer. LMB-02 can be used with Schlage, Corbin/Russwin, Yale, Adams-Rite and similar mortise locks.

      • LMB-03 - Lock Mount Bracket.

        Universal Mounting Bracket.

        Photo by: Major Manufacturing

      • LMB-03 - Universal Mounting Bracket:

        Universal mounting bracket for use in hollow metal or aluminum doors and frames. LMB-03 has different offsets at each end to allow adjustment for an assortment of installations. Holes are tapped 10-32 and supplied with four 10-32 x 1/2" phillips flat mounting screws.

        Packed two brackets and four screws per set. To make installation of this bracket quick, easy and exact, use our HIT-40MB3 drill guide.

      • LMB-04 - Lock Mount Bracket.

        For Deadbolt Or T-Strike In Hollow Metal Frame.

        Photo by: Major Manufacturing

      • LMB-04 - For Deadbolt Or T-Strike In Hollow Metal Frame:

        Mounting bracket used to install 1 1/8" x 2 3/4" deadbolt or T-strikes in hollow metal frames. Supplied with steel pop-rivets for installation and a self-adhesive template to lay out mounting holes and strike cut-out.

        Strike mounting holes pre-tapped 8-32. Packed two brackets with pop-rivets and template per pack.

      • LMB-05 - Lock Mount Bracket.

        For ASA Strike Threaded 12-24.

        Photo by: Major Manufacturing

      • LMB-05 - For ASA Strike Threaded 12-24:

        Same as LMB-04 only used with 1-1/4" x 4-7/8" ASA strikes. Supplied with steel pop-rivets for installation and a selfadhesive template to lay out mounting holes and strike cut-out.

        Strike mounting holes pre-tapped 12-24. Packed two brackets with pop-rivets and template per pack.

      • LMB-06 - Lock Mount Bracket.

        Replacement Steel Rod Guide - Square Hole.

        Photo by: Major Manufacturing

      • LMB-06 - Replacement Steel Rod Guide - Square Hole:

        Direct replacement steel rod guide with square hole for Builders Brass, International and Trimco flush bolts.

        Stronger than the plastic guides supplied by the manufacturer. Mounting holes are pre-tapped 8-32. Packed one per pack with mounting screws.

      • LMB-07 - Lock Mount Bracket.

        Replacement Steel Rod Guide - Hex Hole.

        Photo by: Major Manufacturing

      • LMB-07 - Replacement Steel Rod Guide - Hex Hole:

        Replacement steel rod guide with hex hole for use with W&F, Reflectolite and Slideco aluminum door locks equipped with top and bottom rods.

        Stronger than the plastic guides supplied by the manufacturer. Mounting holes are pre-tapped 8-32. Packed one per pack with mounting screws.

      • LMB-08 - Lock Mount Bracket.

        For Adams Rite Style Locks.

        Photo by: Major Manufacturing

      • LMB-08 - For Adams Rite Style Locks:

        LMB-08 supplied with adapters to conform to flat, radius or bevel face doors. Never be without the right bracket. Build-in screw jacks eliminate slipping, twisting and screw stripping during installation.

      • LMB-10 - Lock Mount Bracket.

        For Tubular Latch In Wood Door.

        Photo by: Major Manufacturing

      • LMB-10 - For Tubular Latch In Wood Door:

        Re-enforcing bracket used to repair and strengthen the latch area of a wood door. Simply mortise bracket into damaged latch area, mount with wood screws (supplied) and install latch. Zinc plated.

      • LMB-11 - Lock Mount Bracket.

        For Tubular Latch In Hollow Metal Door.

        Photo by: Major Manufacturing

      • LMB-11 - For Tubular Latch In Hollow Metal Door:

        Economy version of our LMB-01 bracket. Mounts to steel door with four 8-32 screws (supplied). Not suitable for use on steel doors with a center seam. Zinc plated.

      • LMB-12 - Lock Mount Bracket.

        For Mortise Lock In Hollow Metal Frame.

        Photo by: Major Manufacturing

      • LMB-12 - For Mortise Lock In Hollow Metal Frame:

        Economy version of our LMB-02 bracket. Mounts to steel door with four 8-32 screws (supplied). Not suitable for use on steel doors with a center seam. Zinc plated.

      • LMB-15A - Lock Mount Bracket.

        For Adams Rite Levers & Paddles.

        Photo by: Major Manufacturing

      • LMB-15A - For Adams Rite Levers & Paddles:

        Use these brackets when installing a dead latch lock where a dead bolt with an indicator was taken out. The LMB-15 will cover the indicator cut out plus provide the lower mounting hole for the paddle or lever.

        The overall size is 1-5/16" X 5-3/4� X 1/8" thick. The LMB-15 is available in both aluminum and duranodic powdercoat finishes.

      • LMB-15D - Lock Mount Bracket.

        For Adams Rite Levers & Paddles.

        Photo by: Major Manufacturing

      • LMB-15D - For Adams Rite Levers & Paddles:

        Use these brackets when installing a dead latch lock where a dead bolt with an indicator was taken out. The LMB-15 will cover the indicator cut out plus provide the lower mounting hole for the paddle or lever.

        The overall size is 1-5/16" X 5-3/4" X 1/8" thick. The LMB-15 is available in both aluminum and duranodic powdercoat finishes.

      • LMB-033 - Lock Mount Bracket.

        For A/R Locks In Radius Door Frames.

        Photo by: Major Manufacturing

      • LMB-033 - For A/R Locks In Radius Door Frames:

        Use these brackets when installing an Adams Rite style lock in an aluminum frame door. One end of the bracket is offset for use with radius doors, the other end is flat and designed for radius doors with a weather strip channel down the center. These brackets are a must for installing locks in doors that have a deep frame.

        All mounting holes are tapped 10-32 and both zinc and black screws, for aluminum and duranodic color doors and rubber spacers are supplied. The brackets are 1" wide and 2-1/2" long and are zinc plated to resist rust.

        2 brackets per pack with fasteners. To make installation of this bracket quick, easy and exact, use our HIT-40MB3 drill guide.

      • LMB-034 - Lock Mount Bracket.

        For A/R Locks In Bevel Door Frames.

        Photo by: Major Manufacturing

      • LMB-034 - For A/R Locks In Bevel Door Frames:

        Use these brackets when installing an Adams Rite style lock in an aluminum frame door. The LMB-034 bracket was specifically designed for mounting locks in a beveled door frame. These brackets are a must for installing locks in doors that have a deep frame.

        All mounting holes are tapped 10-32 and supplied with zinc and black mounting screws, for aluminum and duranodic color doors. The brackets are 1" wide and 2-1/2" long and are zinc plated to resist rust. Reversable for both right and left hand doors.

        2 brackets with fasteners per package. To make installation of this bracket quick, easy and exact, use our HIT-40MB3 drill guide.

      • LMB-089.

        Installation Tool For LMB-08.

        Photo by: Major Manufacturing

      • LMB-089 - Installation Tool For:

        Quickly locate and install LMB-08 brackets with the LMB-089 Installation Tool. Brackets are screwed to installation tool to prevent them from slipping off during installation.

        Once brackets and tool are inserted into door channel, brackets are rotated 90 degrees and will lock in the correct position for installation.

        Simply slide tool to top of the faceplate cutout, tighten bracket in place, remove the holding screw, slide tool to bottom of cutout, tighten bottom bracket, and remove holding screw and tool.

      • LMB-100.

        Lock Mount Bracket Kit.

        Photo by: Major Manufacturing

      • LMB-100 - Lock Mount Bracket Kit:

        Have all the brackets you need for an installation or repair job organized neatly in a kit. Brackets are included for aluminum door locks and flush bolts, mortise and cylindrical locks. There is even a bracket to repair a wood door latch.

        Purchased separately this kit would cost over $350.00 to put together. The following brackets and installation tool included in this kit:

        2 LMB-01, 2 LMB-011, 2 LMB-10, 2 LMB-02, 2 LMB-12, 2 LMB-04, 2 LMB-05, 2 LMB-03, 2

        LMB-033, 2 LMB-034, 2 LMB-08, 1 LMB-089 TOOL, 2 LMB-06, 2 LMB-07, 1 LMB-15A, 1 LMB-15D.


PATIO DOOR LOCKS


      • Octopod 5002-1-40A - 40" Rod.

        Aluminum Powdercoat Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-1-40A - 40" Rod - Aluminum Powdercoat Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. Aluminum Powdercoat - 3/8" diameter x 40" Locking Rod - #1 Gear for Standard mortise cylinders. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including three rod guides and both Phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-1-40B - 40" Rod.

        Brass Plated Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-1-40B - 40" Rod - Brass Plated Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. Brass Plated - 3/8" diameter x 40" Locking Rod - #1 Gear for Standard mortise cylinders. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including three rod guides and both Phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-1-40C - 40" Rod.

        Chrome Plated Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-1-40C - 40" Rod - Chrome Plated Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. Chrome Plated - 3/8" diameter x 40" Locking Rod - #1 Gear for Standard mortise cylinders. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including three rod guides and both Phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-1-40D - 40" Rod.

        Duranodic Powdercoat Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-1-40D - 40" Rod - Duranodic Powdercoat Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. Duranodic Powdercoat - 3/8" diameter x 40" Locking Rod - #1 Gear for Standard mortise cylinders. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including three rod guides and both Phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-1-40W - 40" Rod.

        White Powdercoat Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-1-40W - 40" Rod - White Powdercoat Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. White Powdercoat - 3/8" diameter x 40" Locking Rod - #1 Gear for Standard mortise cylinders. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including three rod guides and both Phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-1-9A - 9" Rod.

        Aluminum Powdercoat Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-1-9A - 9" Rod - Aluminum Powdercoat Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. Aluminum Powdercoat - 3/8" diameter x 9" Locking Rod - #1 Gear for standard mortise cylinders. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including one rod guide and both Phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-1-9B - 9" Rod.

        Brass Plated Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-1-9B - 9" Rod - Brass Plated Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. Aluminum Powdercoat - 3/8" diameter x 9" Locking Rod - #1 Gear for standard mortise cylinders. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including one rod guide and both Phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-1-9C - 9" Rod.

        Chrome Plated Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-1-9C - 9" Rod - Chrome Plated Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. Chrome Plated - 3/8" diameter x 9" Locking Rod - #1 Gear for standard mortise cylinders. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including one rod guide and both Phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-1-9D - 9" Rod.

        Duranodic Powdercoat Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-1-9D - 9" Rod - Duranodic Powdercoat Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. Duranodic Powdercoat - 3/8" diameter x 9" Locking Rod - #1 Gear for standard mortise cylinders. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including one rod guide and both Phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-1-9W - 9" Rod.

        White Powdercoat Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-1-9W - 9" Rod - White Powdercoat Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. White Powdercoat - 3/8" diameter x 9" Locking Rod - #1 Gear for standard mortise cylinders. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including one rod guide and both Phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-2-9A Medeco - 9" Rod.

        Aluminum Powdercoat Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-2-9A Medeco - 9" Rod - Aluminum Powdercoat Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. Aluminum Powdercoat - 3/8" diameter x 9" Locking Rod - #2 Gear for Medeco mortise cylinders. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including one rod guide and both Phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-2-9B Medeco - 9" Rod.

        Brass Plated Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-2-9B Medeco - 9" Rod - Brass Plated Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. Brass Plated - 3/8" diameter x 9" Locking Rod - #2 Gear for Medeco mortise cylinders. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including one rod guide and both Phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-2-9C Medeco - 9" Rod.

        Chrome Plated Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-2-9C Medeco - 9" Rod - Chrome Plated Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. Chrome Plated - 3/8" diameter x 9" Locking Rod - #2 Gear for Medeco mortise cylinders. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including one rod guide and both Phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-2-9D Medeco - 9" Rod.

        Duranodic Powdercoat Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-2-9D Medeco - 9" Rod - Duranodic Powdercoat Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. Duranodic Powdercoat - 3/8" diameter x 9" Locking Rod - #2 Gear for Medeco mortise cylinders. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including one rod guide and both Phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-2-9W Medeco - 9" Rod.

        White Powdercoat Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-2-9W Medeco - 9" Rod - White Powdercoat Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. White Powdercoat - 3/8" diameter x 9" Locking Rod - #2 Gear for Medeco mortise cylinders. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including one rod guide and both Phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-4-9A IC Core - 9" Rod.

        Aluminum Powdercoat Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-4-9A IC Core - 9" Rod - Aluminum Powdercoat Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. Aluminum Powdercoat - 3/8" diameter x 9" Locking Rod - #4 Gear for GMS Interchangeable core housing. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including one rod guide and both phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-4-9B IC CORE - 9" Rod.

        Brass Plated Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-4-9B IC CORE - 9" Rod - Brass Plated Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. Brass Plated - 3/8" diameter x 9" Locking Rod - #4 Gear for GMS Interchangeble core housing. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including one rod guide and both phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-4-9C IC CORE - 9" Rod.

        Chrome Plated Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-4-9C IC Core - 9" Rod - Chrome Plated Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. Chrome Plated - 3/8" diameter x 9" Locking Rod - #4 Gear for GMS Interchangeable core housing. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including one rod guide and both phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-4-9D IC Core - 9" Rod.

        Duranodic Powdercoat Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-4-9D IC Core - 9" Rod - Duranodic Powdercoat Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. Duranodic Powdercoat - 3/8" diameter x 9" Locking Rod - #4 Gear for GMS Interchangeble core housing. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including one rod guide and both phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5002-4-9W IC Core - 9" Rod.

        White Powdercoat Single Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5002-4-9W IC Core - 9" Rod - White Powdercoat Single Point Patio Lock:

        5002 Series Single Point / 1 Locking Rod. White Powdercoat - 3/8" diameter x 9" Locking Rod - #4 Gear for GMS Interchangeble core housing. A 360 degree rotation of the key will drive the locking rod 2 3/8 inches.

        All required parts for installation supplied including one rod guide and both phillips and one-way screws, cylinder is not included. Requires a 1-1/8 inch mortise cylinder.

      • Octopod 5202-1-88A - 40/48" Rods.

        Aluminum Powdercoat Double Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5202-1-88A - 40/48" Rods - Aluminum Powdercoat Double Point Patio Lock:

        5202 Series Double Point / 2 Locking Rods. Surface mounted on the inside of door in either the horizontal or vertical position. A 360 degree rotation of the key will simultaneously drive both rods 2 3/8 inches.

        May be reverse mounted with only the cylinder exposed from the outside. Octopod 5202 Series are supplied with six rod guides and both Phillips and one-way screws and all parts needed for installation except cylinder. Requires a 1 1/8 inch mortise cylinder.

      • Octopod 5202-1-88B - 40/48" Rods.

        Brass Double Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5202-1-88B - 40/48" Rods - Brass Double Point Patio Lock:

        5202 Series Double Point / 2 Locking Rods. Brass - one 40" and one 48" Locking Rod - #1 Gear for Standard mortise cylinders. Surface mounted on the inside of door in either the horizontal or vertical position. A 360 degree rotation of the key will simultaneously drive both rods 2 3/8 inches.

        May be reverse mounted with only the cylinder exposed from the outside. Octopod 5202 Series are supplied with six rod guides and both Phillips and one-way screws and all parts needed for installation except cylinder. Requires a 1 1/8 inch mortise cylinder.

      • Octopod 5202-1-88C - 40/48" Rods.

        Chrome Double Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5202-1-88C - 40/48" Rods - Chrome Double Point Patio Lock:

        5202 Series Double Point / 2 Locking Rods. Chrome - one 40" and one 48" Locking Rod - #1 Gear for Standard mortise cylinders. Surface mounted on the inside of door in either the horizontal or vertical position. A 360 degree rotation of the key will simultaneously drive both rods 2 3/8 inches.

        May be reverse mounted with only the cylinder exposed from the outside. Octopod 5202 Series are supplied with six rod guides and both Phillips and one-way screws and all parts needed for installation except cylinder. Requires a 1 1/8 inch mortise cylinder.

      • Octopod 5202-1-88D - 40/48" Rods.

        Duanodic Powdercoat Double Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5202-1-88D - 40/48" Rods - Duanodic Powdercoat Double Point Patio Lock:

        5202 Series Double Point / 2 Locking Rods. Duanodic Powdercoat - one 40" and one 48" Locking Rod - #1 Gear for Standard mortise cylinders. Surface mounted on the inside of door in either the horizontal or vertical position. A 360 degree rotation of the key will simultaneously drive both rods 2 3/8 inches.

        May be reverse mounted with only the cylinder exposed from the outside. Octopod 5202 Series are supplied with six rod guides and both Phillips and one-way screws and all parts needed for installation except cylinder. Requires a 1 1/8 inch mortise cylinder.

      • Octopod 5202-1-88W - 40/48" Rods.

        White Powdercoat Double Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5202-1-88W - 40/48" Rods - White Powdercoat Double Point Patio Lock:

        5202 Series Double Point / 2 Locking Rods. White Powdercoat - one 40" and one 48" Locking Rod - #1 Gear for Standard mortise cylinders. Surface mounted on the inside of door in either the horizontal or vertical position. A 360 degree rotation of the key will simultaneously drive both rods 2 3/8 inches.

        May be reverse mounted with only the cylinder exposed from the outside. Octopod 5202 Series are supplied with six rod guides and both Phillips and one-way screws and all parts needed for installation except cylinder. Requires a 1 1/8 inch mortise cylinder.

      • Octopod 5202-1-96A - 48" Rods.

        Aluminum Powdercoat Double Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5202-1-96A - 48" Rods - Aluminum Powdercoat Double Point Patio Lock:

        5202 Series Double Point / 2 Locking Rods. Aluminum Powdercoat - 48" Locking Rods - #1 Gear for Standard mortise cylinders. Surface mounted on the inside of door in either the horizontal or vertical position. A 360 degree rotation of the key will simultaneously drive both rods 2 3/8 inches.

        May be reverse mounted with only the cylinder exposed from the outside. Octopod 5202 Series are supplied with six rod guides and both Phillips and one-way screws and all parts needed for installation except cylinder. Requires a 1 1/8 inch mortise cylinder.

      • Octopod 5202-1-96B - 48" Rods.

        Brass Double Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5202-1-96B - 48" Rods - Brass Double Point Patio Lock:

        5202 Series Double Point / 2 Locking Rods. Brass - 48" Locking Rods - #1 Gear for Standard mortise cylinders. Surface mounted on the inside of door in either the horizontal or vertical position. A 360 degree rotation of the key will simultaneously drive both rods 2 3/8 inches.

        May be reverse mounted with only the cylinder exposed from the outside. Octopod 5202 Series are supplied with six rod guides and both Phillips and one-way screws and all parts needed for installation except cylinder. Requires a 1 1/8 inch mortise cylinder.

      • Octopod 5202-1-96C - 48" Rods.

        Chrome Double Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5202-1-96C - 48" Rods - Chrome Double Point Patio Lock:

        5202 Series Double Point / 2 Locking Rods. Chrome- 48" Locking Rods - #1 Gear for Standard mortise cylinders. Surface mounted on the inside of door in either the horizontal or vertical position. A 360 degree rotation of the key will simultaneously drive both rods 2 3/8 inches.

        May be reverse mounted with only the cylinder exposed from the outside. Octopod 5202 Series are supplied with six rod guides and both Phillips and one-way screws and all parts needed for installation except cylinder. Requires a 1 1/8 inch mortise cylinder.

      • Octopod 5202-1-96D - 48" Rods.

        Duranodic Powdercoat Double Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5202-1-96D - 48" Rods - Duranodic Powdercoat Double Point Patio Lock:

        5202 Series Double Point / 2 Locking Rods. Duranodic Powdercoat- 48" Locking Rods - #1 Gear for Standard mortise cylinders. Surface mounted on the inside of door in either the horizontal or vertical position. A 360 degree rotation of the key will simultaneously drive both rods 2 3/8 inches.

        May be reverse mounted with only the cylinder exposed from the outside. Octopod 5202 Series are supplied with six rod guides and both Phillips and one-way screws and all parts needed for installation except cylinder. Requires a 1 1/8 inch mortise cylinder.

      • Octopod 5202-1-96W - 48" Rods.

        White Powdercoat Double Point Patio Lock.

        Photo by: Major Manufacturing

      • Octopod 5202-1-96W - 48" Rods - White Powdercoat Double Point Patio Lock:

        5202 Series Double Point / 2 Locking Rods. White Powdercoat- 48" Locking Rods - #1 Gear for Standard mortise cylinders. Surface mounted on the inside of door in either the horizontal or vertical position. A 360 degree rotation of the key will simultaneously drive both rods 2 3/8 inches.

        May be reverse mounted with only the cylinder exposed from the outside. Octopod 5202 Series are supplied with six rod guides and both Phillips and one-way screws and all parts needed for installation except cylinder. Requires a 1 1/8 inch mortise cylinder.


SECRET GATE LATCH


      • S200-SPA - Secret Gate Latch.

        Plated Chrome Finish.

        Photo by: Major Manufacturing

      • S200-SPA - Secret Gate Latch - Plated Chrome Finish:

        The S200-SPA, Secret Gate Latch has a die cast body and a plated chrome finish. The hidden button in bottom of the case retracts latch for the informed. The exposed dummy knob frustrates the unwelcome intruder.

        For use on "bank type" office gates where minimum security is required. The latch is reversible for right or left hand. Supplied with strike plate, mounting screws and dummy knob. Approximate case size is 2" x 2-1/2".

      • S200-SPB - Secret Gate Latch.

        Plated Brass Finish.

        Photo by: Major Manufacturing

      • S200-SPB - Secret Gate Latch - Plated Brass Finish:

        The S200-SPB, Secret Gate Latch has a die cast body and a plated brass finish. The hidden button in bottom of the case retracts latch for the informed. The exposed dummy knob frustrates the unwelcome intruder.

        For use on "bank type" office gates where minimum security is required. The latch is reversible for right or left hand. Supplied with strike plate, mounting screws and dummy knob. Approximate case size is 2" x 2-1/2".


SUPER STRIKE PLATES


      • SS-610C Super Strike.

        10" X 2" Chrome Finish.

        Photo by: Major Manufacturing

      • SS-610C - Super Strike 10" X 2" Chrome Finish:

        Re-enforced plate for electric strikes in wood frames. Will fit Trine 001 and similar size strikes. 10" x 2" chrome finish. Supplied with fasteners.

      • SS-620B Super Strike.

        10" X 1-3/4" Brass Finish.

        Photo by: Major Manufacturing

      • SS-620B - Super Strike 10" X 1-3/4" Brass Finish:

        Designed for mortise lock sets. Brass finish. 10" x 1-3/4". Supplied with fasteners.

      • SS-620C Super Strike.

        10" X 1-3/4" Chrome Finish.

        Photo by: Major Manufacturing

      • SS-620C - Super Strike 10" X 1-3/4" Chrome Finish:

        Designed for mortise lock sets. Chrome finish. 10" x 1-3/4". Supplied with fasteners.

      • SS-630B Super Strike.

        6" X 1" Brass Finish.

        Photo by: Major Manufacturing

      • SS-630B - Super Strike 6" X 1" Brass Finish:

        Designed for tubular deadbolt locks. Brass finish. 6" x 1". Supplied with fasteners.

      • SS-630C Super Strike.

        6" X 1" Chrome Finish.

        Photo by: Major Manufacturing

      • SS-630C - Super Strike 6" X 1" Chrome Finish:

        Designed for tubular deadbolt locks. Chrome finish. 6" x 1". Supplied with fasteners.

      • SS-640B Super Strike.

        6" X 1-1/8" Brass Finish.

        Photo by: Major Manufacturing

      • SS-640B - Super Strike 6" X 1-1/8" Brass Finish:

        Lip strike designed for key in knob type locks. Brass finish. 6" x 1-1/8". Supplied with fasteners.

      • SS-640C Super Strike.

        6" X 1-1/8" Chrome Finish.

        Photo by: Major Manufacturing

      • SS-640C - Super Strike 6" X 1-1/8" Chrome Finish:

        Lip strike designed for key in knob type locks. Chrome finish. 6" x 1-1/8". Supplied with fasteners.

      • SS-660B Super Strike.

        7-5/8" X 1-3/8" Brass Plated.

        Photo by: Major Manufacturing

      • SS-660B - Super Strike 7-5/8" X 1-3/8" Brass Plated:

        Re-enforced plate designed for jimmy proof dead locks. Brass plated. 7-5/8" x 1-3/8". Supplied with fasteners.

Aiello's Locksmiths of Atlanta (404) 456-3817 - Stock Pictures Locksmith Photo Image Gallery